DosBox Capture Codec: Difference between revisions

From MultimediaWiki
Jump to navigation Jump to search
(started data format description)
m (→‎Data Format: byte 0 vs. first byte for clarity)
 
(13 intermediate revisions by 9 users not shown)
Line 1: Line 1:
* FourCC: ZMBV
* FourCC: ZMBV
* Samples: [http://multimedia.cx/samples/zmbv/ http://multimedia.cx/samples/zmbv/]
* Samples: http://samples.mplayerhq.hu/V-codecs/ZMBV/


This is a codec added to the [http://dosbox.sourceforge.net DosBox] project to capture screen data (like Vmware [[VMNC]]).
This is a codec added to the [http://dosbox.sourceforge.net DosBox] project to capture screen data (like Vmware [[VMNC]]).
Line 10: Line 10:
== Data Format ==
== Data Format ==


The first byte of a ZMBV data chunk contains the following flags:
Byte 0 of a ZMBV data chunk contains the following flags:


  bits 7-2  undefined
  bits 7-2  undefined
  bit 1    delta palette
  bit 1    palette change
  bit 0    1 = intraframe, 0 = interframe
  bit 0    1 = intraframe, 0 = interframe


Line 37: Line 37:
  8  32 bits/pixel
  8  32 bits/pixel


'''NOT FINISHED'''
Presently, only modes 4 (8 bpp), 5 (15 bpp), 6 (16 bpp) and 8 (32 bpp) are supported.
 
If the compression type is 1, the remainder of the data chunk is compressed using the standard zlib package. Decompress the data before proceeding with the next step. Otherwise, proceed to the next step. Also note that you must reset zlib for intraframes.
 
If bit 1 of the frame header (palette change) is set then the first 768 bytes of the uncompressed data represent 256 red-green-blue palette triplets. Each component is one byte and ranges from 0..255.
 
An intraframe consists of 768 bytes of palette data (for palettized modes) and raw frame data.
 
An interframe is comprised of up to three parts:
# if palette change flag was set then first 768 bytes represent XOR'ed palette difference
# block info (2 bytes per block, padded to 4 bytes length)
# block differences
 
Block info is composed from a motion vector and a flag: first byte is (dx << 1) | flag, second byte is (dy << 1). Motion vectors can go out of bounds and in that case you need to zero the out-of-bounds part. Also note that currently motion vectors are limited to a range of (-16..16). Flag tells whether the codec simply copies the block from the decoded offset or copies it and XOR's it with data from block differences. All XORing for 15/16 bpp and 32 bpp modes is done with little-endian integers.
 
Interframe decoding can be done this way:
 
  for each block {
    a = block_info[current_block][0];
    b = block_info[current_block][1];
    dx = a >> 1;
    dy = b >> 1;
    flag = a & 1;
    copy block from offset (dx, dy) from previous frame.
    if (flag) {
    XOR block with data read from stream.
    }
  }


[[Category:Video Codecs]]
[[Category:Video Codecs]]
[[Category:Screen Capture Video Codecs]]

Latest revision as of 22:29, 8 March 2008

This is a codec added to the DosBox project to capture screen data (like Vmware VMNC).

This codec employs ZLIB compression and has intraframes and delta frames. Delta frames seem to have blocks either copied from the previous frame or XOR'ed with some block from the previous frame.

The FourCC for this codec is ZMBV which ostensibly stands for Zip Motion Blocks Video. The data is most commonly stored in AVI files.

Data Format

Byte 0 of a ZMBV data chunk contains the following flags:

bits 7-2  undefined
bit 1     palette change
bit 0     1 = intraframe, 0 = interframe

If the frame is an intra frame as indicated by bit 0 of byte 0, the next 6 bytes in the data chunk are formatted as follows:

byte 1    major version
byte 2    minor version
byte 3    compression type (0 = uncompressed, 1 = zlib-compressed)
byte 4    video format
byte 5    block width
byte 6    block height

Presently, the only valid major/minor version pair is 0/1. A block width or height of 0 is invalid. These are the video modes presently defined:

0  none
1  1 bit/pixel, palettized
2  2 bits/pixel, palettized
3  4 bits/pixel, palettized
4  8 bits/pixel, palettized
5  15 bits/pixel
6  16 bits/pixel
7  24 bits/pixel
8  32 bits/pixel

Presently, only modes 4 (8 bpp), 5 (15 bpp), 6 (16 bpp) and 8 (32 bpp) are supported.

If the compression type is 1, the remainder of the data chunk is compressed using the standard zlib package. Decompress the data before proceeding with the next step. Otherwise, proceed to the next step. Also note that you must reset zlib for intraframes.

If bit 1 of the frame header (palette change) is set then the first 768 bytes of the uncompressed data represent 256 red-green-blue palette triplets. Each component is one byte and ranges from 0..255.

An intraframe consists of 768 bytes of palette data (for palettized modes) and raw frame data.

An interframe is comprised of up to three parts:

  1. if palette change flag was set then first 768 bytes represent XOR'ed palette difference
  2. block info (2 bytes per block, padded to 4 bytes length)
  3. block differences

Block info is composed from a motion vector and a flag: first byte is (dx << 1) | flag, second byte is (dy << 1). Motion vectors can go out of bounds and in that case you need to zero the out-of-bounds part. Also note that currently motion vectors are limited to a range of (-16..16). Flag tells whether the codec simply copies the block from the decoded offset or copies it and XOR's it with data from block differences. All XORing for 15/16 bpp and 32 bpp modes is done with little-endian integers.

Interframe decoding can be done this way:

 for each block {
   a = block_info[current_block][0];
   b = block_info[current_block][1];
   dx = a >> 1;
   dy = b >> 1;
   flag = a & 1;
   copy block from offset (dx, dy) from previous frame.
   if (flag) {
    XOR block with data read from stream.
   }
 }